1.A customer has an existing production fabric with Brocade and McData FC switches intermixed.
When adding an MDS 9000 switch, what MDS interop mode would be required? (Topology: McData
6400 (
ISL) Brocade12000
(
ISL) MDS)
A.Open Fabric Mode
B.Native
C.Interop 1
D.Interop 2
E.Interop 3
Correct:C
2.MDS3_9509# MDS3_9509# dir bootflash: 1106 Dec 08 15:36:14 2003 MDS20031208072937365.lic
1106 Dec 08 15:44:47 2003 MDS20031208074023541.lic 2562 Jun 13 17:25:32 2004
special_config.txt 558 Jun 08 20:25:17 2004 create_mds3_fcalias.script 12288 Dec 04 18:04:10
2003 lost+found/ 12317696 Apr 09 15:41:02 2004 m9500sf1ek9kickstartmz.
1.3.4.bin 12334592
May 05 19:13:47 2004 m9500sf1ek9kickstartmz.
1.3.4b.bin 43659162 Apr 09 15:42:12 2004
m9500sf1ek9mz.
1.3.4.bin 43687917 May 05 19:13:30 2004 m9500sf1ek9mz.
1.3.4b.bin 3222 Mar
26 18:40:02 2004 script_b_fcip Usage for bootflash://suplocal
126206976 bytes used 58352640
bytes free 184559616 bytes total MDS3_95 What command would successfully transfer the
“special_config.txt” file to a workstation, PC, or File Server?
A.copy special_config.txt ftp://<ipaddress>/<path>/special_config.txt
B.copy bootflash:special_config.txt ftp://<ipaddress>/<path>/special_config.txt
C.copy <ftp://bootflash:special_config.txt> <ip address>/<path>/special_config.txt
D.copy <ftp://<ip> address>/<path>/<filename> special_config.txt
E.copy special*.txt ftp://<ipaddress>/<path>/special_config.txt
Correct:B
3.In a long distance link of 100KM, which is true of the desired number of BB credits?
A.More BB credits would cause excessive delay in handling the larger number of packets.
B.The fewer the BB credits there are, the less likely we are to have a packet lost in the network.
C.With fewer BB credits, the transmission pipe will not be full and this will lead to other applications
getting bandwidth should they need it.
D.The FC standard defines the number of credits on a long distance link.
E.None of the above answers are correct.
Correct:E
4.During principal switch selection and the domain ID assignment, all frames are flooded to a
destination ID of this well known fibre channel address:
A.FF.FF.FA
B.FF.FF.FB
C.FF.FF.FC
D.FF.FF.FD
E.FF.FF.FE
Correct:D
5.A Brocade 12000 in its native corePID mode (1) is connected to VSAN 1009 on an MDS. What is
the correct output of the “show vsan 1009″ command?
A.vsan 1009 information name:VSAN1009 state:active interoperability mode:default
loadbalancing:srcid/
dstid/
oxid operational state:up
B.vsan 1009 information name:VSAN1009 state:active interoperability mode:1
loadbalancing:srcid/
dstid/
oxid operational state:up
C.vsan 1009 information name:VSAN1009 state:active interoperability mode:2
loadbalancing:srcid/
dstid/
oxid operational state:up
D.vsan 1009 information name:VSAN1009 state:active interoperability mode:3
loadbalancing:srcid/
dstid/
oxid operational state:up
E.vsan 1009 information name:VSAN1009 state:active interoperability mode:Brocade Native
loadbalancing:srcid/
dstid/
oxid operational state:up
Correct:D
6.You have a legacy JBOD that uses copper DB9
connecters. You want to connect your JBOD to a
Fiber only Fibre Channel switch. You want to convert the DB9
connection to multi mode Fiber
Optics. What device would you use?
A.HSSC
B.MIA
C.GBIC
D.SFP
E.DUAL SC
Correct:B
7.To capture all of the RSCN traffic originating from a standalone switch with no free ports, what
should be utilized?
A.SPAN
B.REMOTE SPAN
C.Ethereal with PAA
D.debug rscn events initiators vsan 1000
E.MDS fcanalyzer
Correct:E
8.You have a host that you connect to a switch port on a MDS switch. The switch port does not
come up and a “show interface” indicates that the port is initializing and eventually goes offline.
You configure the port as a TL port and the port comes up. What type of device is the host?
A.Public loop device
B.Private loop device
C.Non Fibre Channel device
D.The host has a DB9
copper connector
E.The port should not come up after being configured as TL port because TL ports are used to connect to
other switches.
Correct:B
9.MDS Interop mode 2 will interoperate with what legacy Fibre Channel switch below?
A.Brocade 12000 core PID mode 1
B.Brocade 3800 core PID mode 0
C.Inrange FC/9000
D.McData 3900
E.Qlogic Sanbox
Correct:B
10.What is TCP fast recovery?
A.It is an algorithm that uses fast retransmit when a missing segment is detected.
B.It is an algorithm that initiates slow start instead of congestion avoidance after fast retransmit sends
what appears to be the missing segment.
C.It is an algorithm that starts congestion avoidance instead of slow start after fast retransmit sends what
appears to be the missing segment.
D.It is an algorithm that after a new connection is established with a host on another network, initializes
the congestion window to one segment and each time an ACK is received, increases the congestion
window by one segment
Correct:C
11.Before you can successfully enable the Call Home feature, which of the following must be true?
A.snmpserver
contact name defined
B.callhome siteid
defined
C.Enterprise license installed
D.callhome transport email smtpserver
defined
E.snmpserver
location defined
Correct:A
12.What control traffic is NOT prohibited from crossing InterVSAN
boundaries?
A.Fabric Configuration Service (FCS) traffic
B.RSCN and SWRSCN
for devices within the affected IVR zone(s)/active zoneset
C.Build Fabric (BF) and Reconfigure Fabric (RCF) frames
D.Full zoneset distribution traffic
E.ELS frames involved in Principal Switch Selection
Correct:B
13.What settings would be required on a MDS9000 switch for proper use of a PAA?
A.PAA requires a TE port to connect and must be in its own VSAN.
B.PAA requires an SD port and must be it its own VSAN.
C.PAA requires an ethernet connection to the MDS supervisor.
D.PAA requires an SD port connection.
E.PAA requires ST and SD ports.
Correct:D
14.Click the Exhibit button. Assume that FCIP write accelerator has been enabled between MDS1
and MDS2. What will the values of X, Y and Z be in the exhibit?
A.X=50, Y=10, Z=10
B.X=50, Y=ff, Z=10
C.X=10, Y=ff, Z=10
D.X= ff, Y=ff, Z=1
E.X=10, Y=50, Z=10
Correct:C
15.Click the Exhibit button. What module combination per site will fulfill the requirements for this
solution? (Note: Nondisruptive
upgrades must be fully supported at each site.)
A.3 x 16 port module 2 x IPS8
module
B.1 x 16 port module 1 x 32 port module 1 x IPS8
module
C.1 x 16 port module 1 x 32 port module 2 x IPS8
module
D.3 x 16 port module 1 x IPS8
module
E.2 x 32 port module 2 x IPS8
module
Correct:C
16.In Raid 0+1 the loss of a single drive:
A.Does not affect the redundancy of the array
B.Reduces the array redundancy to that of a Raid level 0
C.Same level of redundancy as that of a Raid 1+0
D.Reduces the performance of the array
E.Has no affect what so ever on the array
Correct:B
17.What zoning option is valid in interop mode 2 and 3 with a mixed vendor fabric?
A.domain / port
B.nWWN
C.fcid
D.lun zoning
E.sWWN
Correct:A
18.When transporting full 2148byte
Fibre Channel frames over long distances, which are true?
A.One buffertobuffer
credit is required for every 2 km of distance to support 1 Gbps.
B.Two buffertobuffer
credits are required for every 2 km of distance to support 1 Gbps.
C.One buffertobuffer
credit is required for every 1 km of distance to support 2 Gbps.
D.Two buffertobuffer
credits are required for every 1 km of distance to support 2 Gbps.
E.Three buffertobuffer
credits are required for every 1 km of distance to support 2 Gbps.
Correct:A C
19.Using Device Manager, how can zoning be enabled between Fibre Channel members in the
same VSAN?
A.RightClick
on any live ports and click on “devices” it will list all enabled devices. Select any devices and
click on “Zones”.
B.Click on the menu toolbar “FC” >
“VSAN” >
“Zones” to create zones.
C.Click on the menu toolbar “Interface” >
“FC F/FL/TL” >
“Zones”.
D.Click on the menu toolbar “Admin” >
“Zones”
E.Device Manager does not do Fibre Channel Zoning.
Correct:E
20.The IPS iSCSI gateway has two forwarding modes. An advantage of using “passthru”
mode is?
A.IPS converts and forwards full iSCSI PDU to the Target.
B.IPS creates only one initiator to reduce configuration.
C.IPS converts and forwards one frame at a time which keeps latency low.
D.IPS uses fixed MSS for constant payload to reduce latency.
Correct:C
Link : http://www.killtest.co.kr/CCIE/350-040.asp